Home > Socket Error > Winsock Error 10061 Api Fd_connect

Winsock Error 10061 Api Fd_connect

Contents

Berkeley description: Too many open files. to resolve it select your test project node and add wcf reference. It's very strange –Kobi Guetta May 11 '14 at 5:46 add a comment| 1 Answer 1 active oldest votes up vote 2 down vote Your server is listening on port 4997, This error is returned if either a service provider's DLL could not be loaded (LoadLibrary failed) or the provider's WSPStartup or NSPStartup function failed. http://hardwareyellowpages.com/socket-error/winsock-error-10061-connection-refused-on-api-connect.html

WinSock functions: gethostbyaddr(), gethostbyname(), getprotobyname(), getprotobynumber(), getservbyname(), getservbyport(), WSAAsyncGetProtoByName(), WSAAsyncGetProtoByNumber(), WSAAsyncGetServByName(), WSAAsyncGetServByPort(), WSAAsyncGetHostByAddr(), WSAAsyncGetHostByName(), See also: WSAHOST_NOT_FOUND, WSANO_RECOVERY, WSATRY_AGAIN WSANO_RECOVERY (11003) This is a non-recoverable error Berkeley description: This is a A socket operation was attempted to an unreachable host. Generically, the error means the network system has run out of socket handles. WinSock description: Same as Berkeley, except WinSock doesn't support the sendmsg() function, and some WinSock implementations are not so strict as to require an application with a datagram socket to "disconnect"--by http://help.globalscape.com/help/cuteftp8/Socket_errors_10060_10061_10064_10065.htm

Socket Error 10061 Connection Refused

Berkeley description: A bad option or level was specified in a getsockopt()(2) or setsockopt(2) call. WinSock functions: connect(), sendto(), FD_CONNECT Additional functions: Any function that does network I/O: recv(), recvfrom(), send(), FD_READ, FD_WRITE See also: WSAEHOSTUNREACH WSAENOBUFS (10055) No buffer space available. WinSock functions: gethostbyaddr(), gethostbyname(), getprotobyname(), getprotobynumber(), getservbyname(), getservbyport(), WSAAsyncGetHostByAddr(), WSAAsyncGetHostByName(), WSAAsyncGetProtoByName(), WSAAsyncGetProtoByNumber(), WSAAsyncGetServByName(), WSAAsyncGetServByPort(), See also: WSAHOST_NOT_FOUND, WSANO_DATA, WSATRY_AGAIN WSASYSNOTREADY (10091) Network subsystem is unavailable Berkeley description: No equivalent. recv(), recvfrom(), send(), sendto(): MSG_OOB was specified, but the socket is not of type SOCK_STREAM Developer suggestions: don't do that.

That they are not trying to use more than one Windows Sockets implementation simultaneously. A completion indication will be given later when the operation has been completed. Is the router up and running (check by pinging it, and then ping an address on the other side of it)? Winsock Error 10060 Berkeley description: The system detected an invalid address in attempting to use an argument of a call.

WinSock functions: recv(), recvfrom(), send(), sendto(), FD_CLOSE Additional functions: Any function that does I/O on the network could generate this error. Winsock Error Code 10061 Exchange 2013 Berkeley description: A required address was omitted from an operation on a socket. This may be because the database files (for example, BSD-compatible HOSTS, SERVICES, or PROTOCOLS files) could not be found, or a DNS request was returned by the server with a severe The socket is marked as non-blocking (non-blocking operation mode), and the requested operation is not complete at this time.

User suggestions: see WSAHOST_NOT_FOUND for details. Socket Error 10060 Connection Timed Out I'm running the asp.net development server on port 1212, with a wsHttpBinding. A service provider returned a bogus procedure table to Ws2_32.dll. Note that this error is returned by the operating system, so the error number may change in future releases of Windows.

Winsock Error Code 10061 Exchange 2013

User suggestions: Check your WinSock, protocol stack, network driver and network interface card configuration. Source WinSock functions: gethostbyaddr(), gethostbyname(), WSAAsyncGetHostByAddr(), WSAAsyncGetHostByName(), WSAAsyncGetProtoByName(), WSAAsyncGetProtoByNumber(), WSAAsyncGetServByName(), WSAAsyncGetServByPort() Additional functions: It is strange that the asynchronous protocol and services functions can fail with this error, but the synchronous cannot. Socket Error 10061 Connection Refused WSAEAFNOSUPPORT 10047 Address family not supported by protocol family. Socket Error 10061 Connection Refused Windows 7 Not implemented: name server does not perform specified operation.

However, they don't need to set the WinSock error value, because there's only one reason for their failure: the input parameter was invalid. http://hardwareyellowpages.com/socket-error/winsock-code-10061.html In Berkeley, this error also occurs when you are trying to name the local socket (assign local address and port number) with bind(), but Windows Sockets doesn't ascribe this error to The following list describes the possible error codes returned by the WSAGetLastError function. Alternately, you could call setsockopt(SO_REUSEADDR) to allow duplicate local addresses in a single application, but this is a kludgy approach (i.e. What Is A Socket Error

  • Berkeley description: A directory with entries other than `.'and `..' was supplied to a remove directory or rename call.
  • Check out IPSec setting if you still face problem.
  • You would have caught that if you had included the listening and connecting IP:Port pairs in your debug output to the console.
  • The connection has been broken due to keep-alive activity detecting a failure while the operation was in progress.

WinSock description: Same as Berkeley; the option is unknown or unsupported. Could you be more specific where in properties you configured to use IIS instead of local directory? Note that the v1.1 WinSock specification does not explicitly state that this error occurs if the value you request is larger than the WSAData.iMaxUdpDg returned from WSAStartup(). http://hardwareyellowpages.com/socket-error/winsock-error-10061.html WSA_QOS_EFLOWSPEC 11017 QoS flowspec error.

I am able to pass in an arbitrarily complex object of custom types no problem - but the server tanks with a custom return type. Socket Error 10061 Connection Refused Smtp An invalid or inconsistent flowspec was found in the QOS structure. after the first failed with WSAEWOULDBLOCK).

An invalid value was given for one of the arguments to a function.

I'm trying to invoke free web service http://www.mindreef.net/svc/hashservice/servicesHashClassSoap?wsdl.... a "high-level" protocol). The specified class was not found. Socket Error 10054 I have error 10061 when I'm trying to connect the server. ("error - connect failed.

This error occurs if an application attempts to bind a socket to an IP address/port that has already been used for an existing socket, or a socket that was not closed A socket operation encountered a dead host. Typically, though, WinSock generates this error when it receives a "host unreachable" ICMP message from a router. Check This Out A request to send or receive data was disallowed because the socket had already been shut down in that direction with a previous shutdown call.