Home > Socket Error > Winsock Error 10065 The Host Is Unreachable

Winsock Error 10065 The Host Is Unreachable

Contents

WinSock functions: Additional functions: If a WinSock implementation has an upper limit to the number of simultaneous tasks it can handle, an application's initial call to WSAStartup() could fail with To make these messages easier to understand, let's make an analogy.Cast of characters:Joe is your mIRC, an IRC client.Mary is the IRC server (as are Jane, Helga and Kyoko, all of User suggestions: Check your WinSock, protocol stack, network driver and network interface card configuration. WSAEALREADY 10037 Operation already in progress. http://hardwareyellowpages.com/socket-error/winsock-10065.html

a TCP reset received from remote host). For instance, even if you request to send() a few bytes of data on a newly created TCP connection, send() could fail with WSAEWOULDBLOCK (if, say, the network system has a If not, check with your Winsock vendor to see if they have a newer Winsock available. It can occur if you're trying to run too many applications (of any kind) simultaneously on your machine. http://help.globalscape.com/help/cuteftp8/Socket_errors_10060_10061_10064_10065.htm

10060 Socket Error

With datastream sockets, don't call connect() more than once (use select() or WSAAsyncSelect() to detect connection completion). This normally results if the peer application on the remote host is suddenly stopped, the host is rebooted, the host or remote network interface is disabled, or the remote host uses It is a nonfatal error, and the operation should be retried later.

  1. TCP/IP scenario: description of the TCP/IP protocol suite network traffic (i.e.
  2. The application has tried to determine the status of an overlapped operation which is not yet completed.
  3. Windows Sockets only allows a single blocking operation—per- task or thread—to be outstanding, and if any other function call is made (whether or not it references that or any other socket)
  4. In Berkeley, this error also occurs when you are trying to name the local socket (assign local address and port number) with bind(), but Windows Sockets doesn't ascribe this error to
  5. This is not a temporary error.
  6. Click the LOGIN link in the forum header to proceed.
  7. By calling shutdown() you do a partial close of a socket, which means you have discontinued sending.
  8. So, for example, if a WinSock implementation doesn't support SOCK_RAW with IPPROTO_IP (or any other protocol), then the socket() call would fail with WSAEPROTONOSUPPORT (however, if it doesn't support SOCK_RAW at

Unlike Berkeley, however, WinSock v1.1 doesn't ascribe this error to any functions. WSAEADDRINUSE (10048) Address already in use. The call has been canceled. How To Fix Socket Error 10060 WSAECONNABORTED 10053 Software caused connection abort.

This error is returned if either a service provider's DLL could not be loaded (LoadLibrary failed) or the provider's WSPStartup or NSPStartup function failed. Socket Error 10060 Connection Timed Out Request refused: Name server refuses to satisfy your query for policy reasons. WinSock description: Same as Berkeley. "You can't make a silk purse from a sow's ear." Detailed descriptions: accept(), listen(): socket is not of type that supports connection-oriented service. An invalid or inconsistent flowspec was found in the QOS structure.

The Windows Sockets API does not have analogs for the Berkeley perror() and herror() functions that take the error value as input, and output the (short) text of each error value What Is A Socket Error Some of the types of things you will find under some errors are: Microsoft C description: the first few WinSock errors are carry-overs from the standard 'C' runtime library. Specifically, v1.1 WinSock spec notes that this error occurs if the length of the buffer is too small. An error with the underlying traffic control (TC) API as the generic QoS request was converted for local enforcement by the TC API.

Socket Error 10060 Connection Timed Out

There are only a few possible causes for this error:You tried to connect to the wrong port. WinSock functions: Any function which allocates a new descriptor: accept(), listen(), & socket(). 10060 Socket Error WSAENETRESET 10052 Network dropped connection on reset. Winsock Error 10060 Mdaemon The ICMP message means that the router can"t forward the IP datagram, possibly because it didn"t get a response to the ARP request (which might mean the destination host is down).

This documentation is archived and is not being maintained. this contact form This error is returned by the WSCGetProviderInfo and WSCGetProviderInfo32 functions if the protocol entry specified could not be found. There is another possibility: you are accessing a socket which the current active task does not own (that is, you're trying to share a socket between tasks). Developer suggestions: Chances are, that if you encounter this error, your application ignored the failure of some previous function. Socket Error 10061 Connection Refused

Berkeley description: A component of a path name exceeded 255 (MAXNAMELEN) characters, or an entire path name exceeded 1023 (MAXPATHLEN-1) characters. Wiki Webinars FAQ Advanced Search Forum PRODUCT RELATED DISCUSSIONS FILE & NETWORKING SERVICES iPrint Winsock Error 10065 You can view the discussions, but you must login before you can post. Unfortunately, to find out what these errors mean you need to contact that WinSock provider. have a peek here WinSock description: No equivalent.

WSAEHOSTUNREACH 10065 No route to host. Winsock Error 10061 You can monitor available memory with Program Manager's 'Help/About...' command. Whether to handle it as a fatal error or non-fatal error depends on the application and the context, so it's entirely up to you to decide.

You can monitor available memory with Program Manager's "Help/About..." command.

we don't recommend it). WSAENOTEMPTY 10066 Directory not empty. WinSock description: The Windows Sockets definition of this error is very different from Berkeley. Error Code 10060 Socket Connection Failed In this case, the 2nd application will fail with WSAEADDRINUSE.

For inet_addr(), this could mean the content of the buffer passed or the buffer itself is invalid. Try a traceroute to the destination address to check that all the routers are functioning. The application has initiated an overlapped operation that cannot be completed immediately. http://hardwareyellowpages.com/socket-error/windsock-error-10065.html copies what it can into your buffer) and fails the function.

At least one QoS reserve has arrived. This error occurs if you specifically reference a protocol that isn't part of the address family you also reference. If the hostname resolution uses a local hosttable, it's possible you resolved to an old obsolete address. Here is a useable macro: #define MAKEWORD(low, high) ((WORD)(((BYTE)(low)) | (((WORD)((BYTE)(high))) << 8))) WinSock functions: WSAStartup(). [Go to Top] Errors in Numerical Order WSABASEERR (0) No Error WSAEINTR (10004) Interrupted system

WinSock functions: accept(), close socket(), connect(), recv(), recvfrom(), send(), sendto(), WSAAsyncGetHostByAddr(), WSAAsyncGetHostByName(), WSAAsyncGetProtoByName(), WSAAsyncGetProtoByNumber(), WSAAsyncGetServByName(), WSAAsyncGetServByPort() WSAHOST_NOT_FOUND (11001) Host not found Berkeley description: No such host is known. When a particular Windows Sockets function indicates an error has occurred, this function should be called immediately to retrieve the extended error code for the failing function call.