Home > Socket Error > Wsano_data

Wsano_data

Contents

But if i try after a few minutes, i just cannot connect :-( so the question remains...how do i connect to a remote host using ip address??? The system detected an invalid pointer address in attempting to use a pointer argument of a call. If it persists, exit Windows or reboot your machine to remedy the problem. A reserved policy element was found in the QoS provider-specific buffer.   Requirements Header Winsock2.h; Winerror.h See also Error Codes - errno, h_errno and WSAGetLastError Handling Winsock Errors FormatMessage WSAGetLastError   http://hardwareyellowpages.com/socket-error/wsano-recovery.html

Some error codes defined in the Winsock2.h header file are not returned from any function. WSAEREFUSED 10112 Database query was refused. Watch carefully and see if you can tell whether your program is starting before you see the login complete. It can occur if you're trying to run too many applications (of any kind) simultaneously on your machine.

Socket Error 10054

Login. Sosomething like...DWORD addr = MAKEIPADDRESS(192, 168, 241, 106);gethostbyaddr((char*)&addr, 4, AF_INET);--Jeff Partch [VC++ MVP]Post by Yaniv MHi,invoking gethostbyaddr failes with error WSANO_DATA (code example isattached).1. WSAEMSGSIZE 10040 Message too long. All Rights Reserved.

  1. To start viewing messages, select the forum that you want to visit from the selection below.
  2. WSAEFAULT 10014 Bad address.
  3. Networking activity on the local host has not been initiated.
  4. Berkeley description: A file descriptor argument was out of range, referred to no open file, or a read (write) request was made to a file that was only open for writing
  5. It's C code combined with some of my own classes...
  6. Berkeley description: Too many open files.
  7. Two functions that are conspicuously absent from the current function list above are shutdown() and close socket().

See ASP.NET Ajax CDN Terms of Use – http://www.asp.net/ajaxlibrary/CDN.ashx. ]]> CodeGuru Home VC++ / MFC / C++ .NET / recv(), recvfrom(), send(), sendto(): MSG_OOB was specified, but the socket is not of type SOCK_STREAM Developer suggestions: don't do that. The WSAGetLastError function returns the last error that occurred for the calling thread. Socket Error 10049 User suggestions: Did you enter a destination hostname?

WinSock description: Same as Berkeley. User suggestions: see WSAECONNABORTED for details. The "address" it refers to is the remote socket name (protocol, port and address). Berkeley description: The quota system ran out of table entries.

Clearly, this oversight was not intentional. Wsagetlasterror 0 The support for the specified socket type does not exist in this address family. Now I can finally establish a reliable connection! Berkeley description: The attempted operation is not supported for the type of object referenced.

What Is A Socket Error

An attempt was made to access a socket in a way forbidden by its access permissions. To start viewing messages, select the forum that you want to visit from the selection below. Socket Error 10054 Now, I've noticed a real degridation in the speed of my dial-up connection (XTRA) after installing Privoxy, and it's not to be completely written off to the problem I have, as Socket Error 10053 Returned by WSARecv and WSARecvFrom to indicate that the remote party has initiated a graceful shutdown sequence.

tab36 is the name of the machine.--With best wishes,Igor Tandetnik"For every complex problem, there is a solution that is simple, neat,and wrong." H.L. Sosomething like...DWORD addr = MAKEIPADDRESS(192, 168, 241, 106);gethostbyaddr((char*)&addr, 4, AF_INET);--Jeff Partch [VC++ MVP]Post by Yaniv MHi,invoking gethostbyaddr failes with error WSANO_DATA (code example isattached).1. SO_ACCEPTCONN, SO_DONTLINGER, SO_KEEPALIVE, SO_LINGER, SO_OOBINLINE and TCP_NODELAY are not supported on sockets of type SOCK_DGRAM. Do you have a router configured? Socket Error 10054 Connection Reset By Peer

Please don't forget to rate users who helped you! Some invalid argument was supplied (for example, specifying an invalid level to the setsockopt function). Is the router up and running (check by pinging it, and then ping an address on the other side of it)? all other functions: retry the operation again later since it cannot be satisfied at this time.

There are no QoS receivers. Wsaeconnreset 10054 WSA_IO_INCOMPLETE 996 Overlapped I/O event object not in signaled state. WSAEBADF (10009) Bad file descriptor.

But most of these function-less errors are simply out of place; they are inappropriate to the Windows Sockets API as it exists in the v1.1 specification.

Can you ping that hostname? This is not a temporary error. If the hostname resolution uses a local hosttable, it's possible you resolved to an old obsolete address. Socket Error 11004 Assuming you have a name server configured instead of or as well as a host table, a hostname resolution request causes a Winsock DLL to send a DNS "A" record query

WSAEPROCLIM 10067 Too many processes. WSAESOCKTNOSUPPORT 10044 Socket type not supported. You can avoid making the mistake of trying to send on a socket after you've initiated a close, by keeping track of the socket state in your application (and checking it the byte-order functions, htonl(), htons(), ntohl and ntohl(), cannot fail.

The occurrence of an unlisted error can provide extra detail. For example, the value given for the origin when positioning a file pointer (by means of a call to fseek) is before the beginning of the file. WSAEBADF 10009 File handle is not valid. WSAStartup may fail with this error if the limit has been reached.

If there is more than one Winsock DLL on your system, be sure the first one in the path is appropriate for the network subsystem currently loaded. WinSock functions: gethostbyaddr(), gethostbyname(), WSAAsyncGetHostByAddr(), WSAAsyncGetHostByName(), WSAAsyncGetProtoByName(), WSAAsyncGetProtoByNumber(), WSAAsyncGetServByName(), WSAAsyncGetServByPort() Additional functions: It is strange that the asynchronous protocol and services functions can fail with this error, but the synchronous cannot. Note that this error is returned by the operating system, so the error number may change in future releases of Windows. WinSock functions: Additional functions: any function that takes a socket (or file handle) as an input parameter See also: WSAENOTSOCK WSAECONNABORTED (10053) Software caused connection abort.

This fills a structure with information about the winsock you are using, so that TCP/IP programs can be made aware of any limitations that exist with your winsock. See also: WSAECONNRESET, WSAENETRESET, WSAETIMEDOUT WSAECONNREFUSED (10061) Connection refused. This could happen with a call to another function later, including connect, listen, WSAConnect, or WSAJoinLeaf. This usually results from trying to connect to a service that is inactive on the foreign host—that is, one with no server application running.