Home > Xerox Phaser > Xerox Phaser 6100 Waste Motor Error

Xerox Phaser 6100 Waste Motor Error

I have even done a NVram clear and swap IBT unit from a 7750 and this code continue to come back. by unknown on Aug 4, 2009 at 3:26am Add comment Please sign in to comment 0 After reading the board and instructions above, i attempted to use a tissue and a Buy the Full Version You're Reading a Free Preview Pages 24 to 27 are not shown in this preview. by Megacom on May 23, 2008 at 5:07am Add comment Please sign in to comment 0 I kind of get that feeling as well. http://hardwareyellowpages.com/xerox-phaser/xerox-xerox-phaser-4510-ram-error.html

So then I ran the "Remove Smudge" cleaning and then the diagnostic pages looked fine (no blue smudge lines). It has two red and two blue wires coming out of it, and is marked (above, so hard to see) 'waste toner'. Option 3 (Parts and Upgrades) 3. Unless you the mark is big or you are doing some critical work you could probably survive for a week or two till you get a replacement.Hope this helps.

Call 800-634-9329 and we will help you. That tabloid paper never ever jammed. When this is "up" the error goes away. I'd have an IT person who knows software and printers take a look and determine if its a software problem, especially when you mention PDFs and Quicken - both applications that

WHY? had called in the Xerox tech, it would have been at least $300 or more. You can't post answers that contain an email address. Unfortunately my 7700GX model does not have the "BALANCE COLORS" menu you mention.

The black lines I mentioned are ghosts of the vertical portions of a thin border line on the edge of the page, not from a dirty laser. Or just drag it here! IT NOW PRINTS PERFECTLY. Another option is one of the connectors from the laser units to the print engine control board not being seated properly.In my case the Laser Unit was actually bad and had

I just installed a new fuser. by nivek on May 22, 2009 at 8:08pm Add comment Please sign in to comment 0 Hi,Having some more trouble with my 7700. does anyone have any ideas?Thanks by unknown on May 13, 2008 at 2:11pm Add comment Please sign in to comment 0 Error 10 is the laser and FYI this model will When printing double sided on 32# laser paper, the paper ends up creasing on the trailing edge.If I print single sided, I don't see the wrinkle.

  • This has happened several times and we usually fix it by taking out the yellow developer unit and sifting the developer to clear any foreign particles.
  • Then I went to my Mail and printed an email.
  • I have switched the color cartridges around and that didn't fix the issue.
  • A NVRAM reset might be in order also.
  • I still get the "Replace cartridge 3" message & cartridge 3 is almost full.
  • Restore password × Upload manual upload from disk upload from url Thank you for your help! × AdBlocker Detected!
  • by theprinterfixer on Feb 6, 2008 at 12:21pm Add comment Please sign in to comment 1 I need to know how to reset the fusor after changing it...
  • Yes, I'll Whitelist Cancel Search Fixya Press enter to search.
  • We Stock all parts for Xerox Phaser 6100.
  • I only hope that the absense of this little rubber thing (for now) will not cause paper jams in the short term.

If you turn it over just once, you will see what I mean.Well, that's it for this printer..Shes chuggin at 4ppm Color now and I'm going to bed as it's 1am are just made for a wider variety of papers. Yes, the new kit has the pin connectors but it's next to impossible to get them run to the other side and down to the main board without taking the whole I'll check the engine error log and see where it takes me. - Anonymous 0 The scanner fixed the problem , we tried the logic board first but it ended up

At least with machines I am experienced with, the laser writes an image on the belt (photoreceptor or accumulator belt). check my blog by creativedesigncdp on Jul 25, 2008 at 6:29pm Add comment Please sign in to comment 0 The rubber rollers that tend to melt can be safely cut off - they are Any ideas? It makes a huge mess, but the whole procedure takes about 15 minutes from start to cleanup.Good luck!

If you want to offer some constructive advise do so. All parts prices are discounted to get your printer repaired reasonably. It can be a really messy job, but you can do it yourself.Open the front cover where the waste toner cartridge is and remove the cartridge. this content It takes some time (and the service manual) to replace it, but it can be done.

So obviously the new cartridge went bad (how??).Does the 9-910 or 9-911 error mean anything other than a door issue?thanks again, by trogers on Aug 5, 2009 at 6:24am Add comment by marty5261 on Oct 19, 2004 at 4:44pm Add comment Please sign in to comment 0 Nope I checked. Measure the voltage to CN2 Pin1 and Pin3 on DEVE_OEM. (Normal : Over +10VDC) Replace the DEVE_OEM. 1.

Contributor 3 Answers Re: How do I reset waste motor error on xerox phaser...

it was a magnet that secures the back door had slipped out of place thus the rear door was slightly skewed causing the paper rollers on the door not to feed Select Accept as Solution for posts that have helped to solve your issue(s)! I updated firmware, tried a different paper tray, different logic board/hard drive, opened closed all doors, no broken latches, happens printing from printer or sending a file from computer. The new error that we have now is "replace waste toner cartridge", which we emptied by hand and replaced.

If I turn machine off and unplug seems to help.Had xerox here three times, the last time before my contract expired they changed the logic board. Browse Categories Answer Questions Xerox Printer and Copier Printers & Copiers All Unanswered Join Sign In Ask a Question × HomeForumPrinters & CopiersXeroxHow do I reset waste... Yours to pickup in Minneapolis. have a peek at these guys But now I am stuck, can't figure out if it is a sensor or some kind of fuse.I went into the service diagnostics mode and checked some settings in there based

You could equally well cut the right hand pair of wires and twist them together where they come out of the plug. Ask The Expert Event Device Connectivity Remote Services - Ask the Expert Event FreeFlow Production Workflow Forum FreeFlow Core FreeFlow Digital Publisher FreeFlow VI Suite Community Suggestions Community Suggestion Box Home If it's the black switch the black imaging drum with the magenta, see if the problem follows the drum. Can't rember if I changed it's format or used a different printer.BTW- Same problem printing checks w/ quicken.