Home > Xerox Phaser > Xerox Phaser 8500 Error Codes

Xerox Phaser 8500 Error Codes

Contents

Deskew Sensor in unexpected state. 1. Replace the EEPROM chip. 4,017.47: This fault code indicates a problem with the process control system. A pivot arm broke off media release assy during removal. The Printhead, mounted to the X- Axis shaft, moves laterally across the surface of the drum. http://hardwareyellowpages.com/xerox-phaser/xerox-phaser-8500-error.html

Development Menu A temporary submenu containing some development functions and access to tests still under development. You da man. Page 49 Phaser 8400/8500/8550/8560 Color Printer Service Manual Single Reduction Belt Drive Pulley Y-Axis Motor Tension Spring Warning Always keep your fingers away from the drum drive system; it uses a If not, it is time to call a technician out to look into replacing the inkloader or printhead (rare).

Xerox Phaser 8560 Error Codes List

Page 139 Phaser 8400/8500/8550/8560 Color Printer Service Manual Service Diagnostics Menu Map (Continued) Menu Function Menu Functions for commanding more complex actions by portions of the printer mechanism. Page 25: Parts Of The Printer, Front View, Right Side View With Printer Interfaces Parts of the Printer Front View Right Side View with Printer Interfaces Phaser 8400/8500/8550/8560 Color Printer Service Page 15: Table Of Contents Jam Codes ................. 3-48 Jam Code Definition Table. After loading the color sticks it and cycling the power it still gave the error.

The Electronics Module has no direct connection to sensors, switches, or solenoids. Page 173: Check Motors Menu Check Motors Menu Phaser 8400/8500/8550/8560 Color Printer Service Manual This test turns on the Y-Axis motor and runs it very slowly for one revolution. There are quite a few parts that need to be correctly set and it's best to have a tech take a look at it. top Xerox.com Support Community Register Sign In Help Support & Drivers MySupport Products & Services Customer Support Forum   Support Forums   Hardware   Phaser 8560DX Error codes Hardware

Page 71: Bist Error Reporting Power-Up Error Messages and LED Codes BIST Error Reporting Phaser 8400/8500/8550/8560 Color Printer Service Manual The printer has three sets of tests that are run when Xerox Phaser 8560 Error Code 07 010 iteminc 7,392 views 4:15 Xerox Colorqube 8570 & 8580 Remanufactured Ink Blocks - Duration: 9:41. Page 147 Phaser 8400/8500/8550/8560 Color Printer Service Manual Wiper Shaft (Continued) Typical Value R# Definition (8400) CCW On fe ripple. 25 to 100 CCW Off fe setting 0.004 to time (sec). Front door - pins broke off arms on each side.

PostedinPrinters, Service RelatedbyLou Cappozzoli < Return to Post List Diegosays: January 6th, 2013 at 12:27 pm I have to face with a xerox phaser 8560 with an error code 07,010.43:201618 if Once installed, place an order through the software for 2 supplies for the machine you want the service reward on, and then let the software run continuously for 30 days. Working... Page 122 3-54 Jam Code Troubleshooting Procedures (Continued) Tray 1 width sensor during Tray 1 pick. 1.

Xerox Phaser 8560 Error Code 07 010

Sign in to add this to Watch Later Add to Loading playlists... Page 161: Check Drive Menu Check Drive Menu Phaser 8400/8500/8550/8560 Color Printer Service Manual This test moves the wiper drive mechanism through the complete range of its motion in each direction Xerox Phaser 8560 Error Codes List Page 95 Phaser 8400/8500/8550/8560 Color Printer Service Manual Troubleshooting Procedure for 13,008 to 13,010 Error Code (Drum Heater) Step Questions and Actions Check that the ambient room temperature is within specifications Page 51: Electronics Module Electronics Module Main Board Configuration Card Phaser 8400/8500/8550/8560 Color Printer Service Manual The Electronics Module includes the main board, the power control board, and the power supply.

Ensure ground integrity for the printer (see “Ensuring Ground Integrity” on page 4-65). http://hardwareyellowpages.com/xerox-phaser/xerox-phaser-error-codes-8560.html Transition MP fe 750 to 1800 min. (mpts). Page 33: Theory Of Operation Theory of Operation In this chapter... ■ Main Printer Subsystems ■ Print Process ■ Printer Self-Maintenance ■ Configuration Card Personality Parameters Chapter... Page 114 3-46 Troubleshooting Procedure for Process Drive Step Questions and Actions Do the Process Drive gears, Transfix Camshaft, and Drum Maintenance Camshaft rotate freely?

  1. Page 19: General Information General Information In this chapter... ■ Printer Introduction and Overview ■ Printer Configurations ■ Control Panel Configuration ■ Parts of the Printer ■ Routine Maintenance Items and
  2. The 7,007.49, 7,008.41, 7009.42, and 7,010.43 errors indicate that the Printhead was unable to tilt normally on its axis.
  3. Time to lift plate up (sec).
  4. Use a less glossy media. 3.
  5. Y-Axis Geometry Typical Value R# Definition (8400) Drum Normalized FFT Power (none) Drum Frequency (hz) Motor FFT Power...
  6. Check printer specifications. 2.
  7. Open the Exit Cover.
  8. A bias force from the lift plate against a rotating cam causes the roller to rotate enough so the missing tooth gear engages the drive train.
  9. Swapping ink feed partsoff an old 8550 that had beenfaithful to me for400k+ copies before it finallyquit.
  10. Page 150 4-20 Tray 1 Pick Shaft (Continued) Typical Value (8400) R# Definition Contact average fe. 120 to 2000 Pushdown MP fe 750 to 2000 max.

Did the test pass? Use Service Diagnostics to run the Wiper Drive test. Does anyone think this is deliberate to make money on the service end of Xerox.....? this content Putting in cracked or broken ink sticks is a no-no.

On the left you should see a big black plastic piece that blocks your view of the front of the printer. jojomascalero 27,214 views 4:08 Xerox Phaser 7750 & 7760 Fan Error Code Fix Part 1 - Duration: 8:44. The printer uses the subtractive color system to produce the colors red, green, and blue.

The process motor stalled during operation.

Off fe settling time (sec). Page 134: Service Diagnostics 30 seconds until the Control Panel indicates Turn the printer power On. s8500-005 1. Is the room too cold or too hot?

If a damaged Wiper Blade catches on the Printhead, it could propel hot liquid ink upward into your face. 30 Sec Printhead Purge Tube Solenoid Valve... I found the sequence for gettinginto the service modeand was able to clear the codesand now it is up and running again. Use this manual as your primary resource for understanding the operational characteristics of the printer and all available options. http://hardwareyellowpages.com/xerox-phaser/xerox-phaser-8560-error-codes-04.html Numbers following the 4th digit represent...